Insulating washer M5 5.3/15/2.4 heat-insulating

Insulating washer M6 6.2/15/2.4 heat-insulating

Nominal diameter inside: 6 mm · Thickness: 2.4 mm · Material: Composite materials · Thread size: M6 · Nominal diameter (thread): 6 mm · Ø inside: 6.2 mm · Ø outside: 15 mm

Insulating washer M8 8.2/15/2.4 heat-insulating

Nominal diameter inside: 8 mm · Thickness: 2.4 mm · Material: Composite materials · Nominal diameter (thread): 8 mm · Ø inside: 8.2 mm · Ø outside: 15 mm · Thread size: M8

swiing® revival membrane seal 0.4 mm | Sachs 50/2, 50/3, 50/4 (A1840)

Material: Oiled paper · Manufacturer: swiing® revival parts · Thickness: 0.4 mm · Hole spacing inlet: 67 mm · Pony OEM number: A1840 · Sachs OEM no.: 0250 106 00

swiing® revival spring for lamp socket

Spring design: Tension spring · Manufacturer: swiing® revival parts · Total length: 27 mm

Thrust washer bearing ring small NOS | Puch Z50

Thickness: 1 mm · Manufacturer: Puch · Material: Steel · Surface: hardened & ground · Ø inside: 16 mm · Ø outside: 27.8 mm · Puch OEM number: 329.1.13.009.1

Inlet gasket 3.2 mm | Puch X30 Velux / Sachs

Place of use: Admission · Thickness: 3.2 mm · Hole spacing inlet: 32 mm

Throttle slide Bing SSB & SSE

Material: Aluminum · Component group Carburetor: Adjusting screws, float, etc. · Carburetor type: SSB · Carburetor type: SSE · Ø outside: 14.4 mm · Height: 24 mm · Alternative version of the Pony OEM number: A1973 · Alternative version of the Pony OEM number: A1974 · Alternative version of the Sachs OEM number: 0261 007 100 · Alternative version of the Sachs OEM number: 0261 007 102

swiing® revival spring chain tensioner Inox | Sachs

Spring design: Torsion spring · Length spring hook: 25 mm · Length spring hook: 40 mm · Manufacturer: swiing® revival parts · Material: Chrome steel (colloquially known as stainless steel) · Area of application: Original · Area of application: Standard · Ø outside: 20 mm · Ø wire: 2.5 mm · Total length: 57 mm · Surface: electropolished · Ø inside: 15 mm

Inlet seal Ø 12 / 0.3 mm | Sachs 502, 50/2

Place of use: Admission · Thickness: 3 mm · Hole spacing inlet: 31 mm · Ø outlet inside: 12 mm · Pony OEM number: A1839 · Sachs OEM no.: 0250 105 000

Insulating washer (5/10/2) Bing SSB carburetor flange M5 (A1829)

Nominal diameter inside: 5 mm · Material: Aluminum · Material: EPDM - Rubber · Nominal diameter (thread): 5 mm · Pony OEM number: A1829 · Sachs OEM no.: 0250 089 000

Clamping washer nut M5 SW8

Material: Steel · Nut type: Nut with clamping part · Thread type: M5x0.8 (standard thread) · Surface: galvanized (blue) · Drive: External hexagon · Nominal diameter (thread): 5 mm · Thread depth: 4 mm · Ø outside: 14.8 mm · Width across flats: 8 mm · Height: 6 mm · Strength class: 8