Replica wire spoke hub made of aluminum with pressed-in bearings for the rear wheel of various mopeds, mopeds and small motorcycles.
Note: The hub is at the limit of tolerances in the area of the brake drum and sprocket mount. The function is just about guaranteed, but you shouldn't expect too much.
The bearings installed are also not of particularly high quality.
You can find suitable add-on parts for the rear hub such as brake pads, clamping screws etc. in the accessories section.
| Material | Aluminum |
| Surface | blank |
| Ø inside | 30 mm |
| Ø axle | 12 mm |
| Ø Receptacle | 93 mm |
| Number of spoke holes | 36 pcs |
| Ø drum | 80 mm |
| Area of application | Standard, Custom |
| Puch |
Ratings
Accessories & related products
Hot 
Brake cable Ø 1.8 mm x 220 cm (pear-shaped nipple)
Ø nipple: 3.5 mm · Ø nipple: 6 mm · Nipple length: 10 mm · Manufacturer: Made in Germany · Material: Steel · Surface: galvanized (blue) · Number of components: 1 pcs · Ø Stranded wire: 1.8 mm · Nipple shape: Pears · Cable length: 2200 mm · Area of application: Standard
EUR 2.90
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Manufacturer: SKF · Ball bearing closed: Yes · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Total length: 190 mm · Width: 8 mm · Width: 9 mm · Ø inside: 12 mm · Ø outside: 28 mm · Ø outside: 29 mm
EUR 37.20
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Ø outside: 91 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 10 mm · Ø External brake pads: 80 mm · Ø axle: 12 mm · Ø bore: 12.2 mm · Ø screw holder: 6.5 mm · Wide cam holder: 12 mm · Total length: 187 mm · Brake lever length (lever length): 55 mm · Cranking (offset): 8 mm
EUR 84.20
swiing® revival rear brake anchor plate | Puch Maxi N
Ø outside: 92 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 10 mm · Ø External brake pads: 80 mm · Ø axle: 12 mm · Ø bore: 12.2 mm · Ø screw holder: 6.5 mm · Wide cam holder: 12 mm · Total length: 135 mm · Brake lever length (lever length): 68 mm · Cranking (offset): 10 mm
EUR 90.20
Magura set screw M6x34 mm lock nut SW10
Slotted: No · Width across flats Screw: 8 mm · Manufacturer: Magura · Ø cable holder: 3.05 mm · Width across flats nut: 10 mm · Material: Brass · Surface: nickel-plated · Thread type: M6x1 (standard thread) · Ø Receptacle: 7.05 mm · Total length: 34 mm · Thread length: 23 mm
EUR 3.00
swiing® revival wheel axle M12x1 x 185 rear (closed ball bearing) | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 11.95 mm · Shank length: 99 mm · Thread type: MF12x1 (fine pitch thread) · Thread length: 28 mm · Thread length: 52 mm · Total length: 185 mm · Width across flats: 7 mm
EUR 11.90
SKF 16101 2RS1 ball bearing 12/30/8
Bearing type: Deep groove ball bearing · Stock number: 16101 · Ø inside: 12 mm · Ø outside: 30 mm · Width: 8 mm · Inner ring width: 8 mm · Manufacturer: SKF · Ball bearing closed: Yes · Dust protection type: 2RS1 - NBR contact seal on both sides · Bearing clearance: CN (standard) · Bearing cage: Sheet steel cage ball-guided · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Area of application: Standard
EUR 19.60
Moped fans also bought
GPO 38 mm cylinder head original | Puch Maxi S, N / X30 NS, NL, N-2AH
Manufacturer: GPO · Material: Aluminum · Surface: sandblasted · Height: 55 mm · Area of application: Standard · Ø cylinder: 38 mm · Width: 125 mm · Total length: 135 mm · Candle thread: short · Number of fixing points: 4 pcs · Hole pattern [mm]: 44 x 44 · Decompressor: No
EUR 39.60
GPO 17" spoke set incl. nipple (2.9 x 188 mm) Inox
Nipple length: 14 mm · Manufacturer: GPO · Material: Chrome steel (colloquially known as stainless steel) · Surface: raw · Quantity: 36 pcs · Length from hook: 188 mm · Nominal diameter (thread): 3.15 mm · Ø spoke head: 5.35 mm · Ø spoke: 2.9 mm · Ø nipple head: 7.9 mm · Ø Nipple neck: 5 mm · Hook length: 9 mm · Hook angle: 95 ° · Thread length: 11 mm · Color: silver
EUR 66.10
swiing® ingenious wheel axle with bearing conversion kit spoke hub front | Puch
Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø inside: 12 mm · Ø outside: 29.02 mm · Total length: 165 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Height: 5.9 mm · Height: 9.9 mm · Ø shaft: 11.95 mm · Thread type: MF12x1 (fine pitch thread) · Shank length: 74.5 mm · Width across flats: 19 mm · Thread length: 40.5 mm · Thread length: 50 mm
EUR 46.90
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Ø outside: 91 mm · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 10 mm · Ø External brake pads: 80 mm · Ø axle: 12 mm · Ø bore: 12.2 mm · Ø screw holder: 6.5 mm · Wide cam holder: 12 mm · Total length: 187 mm · Brake lever length (lever length): 55 mm · Cranking (offset): 8 mm
EUR 84.20
Collection only possible with online purchase and appointment.
