High-quality M12x185 mm thru axle for your Puch moped / moped with LELEU or Grimeca wheel hub in the rear 5-spoke rim.
The rear wheel axle includes all required washers, nuts and spacers.
The cable ties show you where the individual parts should be fitted.
- Red cable tie: hub
- Blue cable ties: swingarm
- green cable tie: brake anchor plate
Notes: This wheel axle is not suitable for Snowflake cast rims.
Complete wheel axle sets with the corresponding industrial bearings can be found in the accessories section.
Nostalgic product for the highest demands of the quality brand swiing®.
| Surface | galvanized (blue) |
| Width across flats | 19 mm |
| Total length | 185 mm |
| Manufacturer | swiing® revival parts |
| Ø shaft | 11.9 mm |
| Material | Steel |
| Thread type | MF12x1 (fine pitch thread) |
| Ø outside | 11.8 mm |
| Shank length | 100 mm |
| Thread length | 26 mm, 52.5 mm |
| Puch |
Ratings
Accessories & related products
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Manufacturer: SKF · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 28 mm · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Width: 8 mm · Width: 9 mm · Ball bearing closed: Yes
EUR 37.20
swiing® ingenious wheel axle with bearing conversion kit Snowflake rear wheel | Puch Maxi
Manufacturer: swiing® ingenious parts · Material: Chrome steel (colloquially known as stainless steel) · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Total length: 185 mm · Ball bearing closed: Yes
EUR 72.10
Not in stock
Moped fans also bought
GPO sprocket 45 teeth black | Puch Maxi, Puch X30 NG-2AH
Manufacturer: GPO · Material: Steel · Surface: powder-coated · Chain pitch: 1/2" x 3/16" · Chain type: 415H · Number of teeth: 45 pcs · Ø bolt circle: 105.5 mm · Ø inside: 94 mm · Ø mounting hole: 6.7 mm · Thickness: 4.5 mm · Hole spacing: 36.5 mm · Hole spacing 2: 68 mm · Cranking (offset): 8 mm · Number of fixing points: 6 pcs · Color: black
EUR 24.00
NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi
Bearing type: Deep groove ball bearing · Stock number: 6001 · Ø inside: 12 mm · Ø outside: 28 mm · Width: 8 mm · Inner ring width: 12 mm · Manufacturer: NTN · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Bearing cage: Sheet steel cage ball-guided · Groove ring: No · Material: Plastic · Material: Steel · Surface: blank · Area of application: Standard
EUR 7.10
Cast wheel hub | Puch Maxi, X30 NG-2AH
Area of application: Tuning · Color: silver · Material: Aluminum · Surface: blank · Surface: raw · Total length: 105 mm · Ø axle: 12 mm · Ø mounting hole: 6.1 mm · Ø inside: 27.9 mm · Ø drum: 80 mm · Ø outside: 114.7 mm · Thread type: FG34.8 (1.37" 24G) · Ø bolt circle: 105 mm · Thread length: 12 mm · Number of fixing points: 12 pcs
EUR 108.30
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Manufacturer: SKF · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 28 mm · Ø outside: 29 mm · Ø inside: 12 mm · Total length: 190 mm · Width: 8 mm · Width: 9 mm · Ball bearing closed: Yes
EUR 37.20
swiing® revival rear brake anchor plate | Puch Maxi S, X30 NG
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 91 mm · Ø External brake pads: 80 mm · Ø axle: 12 mm · Ø shaft: 10 mm · Ø bore: 12.2 mm · Ø screw holder: 6.5 mm · Wide cam holder: 12 mm · Total length: 187 mm · Brake lever length (lever length): 55 mm · Cranking (offset): 8 mm
EUR 84.20
swiing® ingenious wheel axle with bearing conversion kit cast hub front | Puch
Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Thread type: MF12x1 (fine pitch thread) · Ø shaft: 11.95 mm · Ø outside: 29.02 mm · Total length: 165 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Ø inside: 12 mm · Width: 34.5 mm · Height: 5.9 mm · Height: 9.9 mm · Thread length: 40.5 mm · Thread length: 50 mm · Shank length: 74.5 mm · Width across flats: 19 mm · Ball bearing closed: Yes
EUR 46.90
Collection only possible with online purchase and appointment.
