Socket axle set with closed groove ball bearings (Ø 29 mm) for front cast hubs (Leleu) on your Puch moped / moped.
The threaded shaft set consists of a 165 mm long wheel axle, two special ball bearings and all required nuts and spacers.
The wheel axle set works with Leleu front wheel hubs, which are installed in cast rims.
The cable ties show you where to fit what:
- Red cable tie: wheel hub
- green cable tie: brake anchor plate
- Yellow cable tie: Replacement disk for the speedometer drive (the disk is removed if a drive is fitted)
- Blue cable ties: fork braces
Note: When mounting the ball bearings, it is important to note that the long spacer bush between the two ball bearings must be clamped to ensure that the two bearings press with the inner ring on the bushing. If this is not observed, the ball bearings will inevitably jam.
| Manufacturer | swiing® ingenious parts |
| Ball bearing closed | Yes |
| Material | Steel |
| Surface | galvanized (blue) |
| Ø inside | 12 mm |
| Total length | 165 mm |
| Ø outside | 29.02 mm |
| Width across flats | 19 mm |
| Thread type | MF12x1 (fine pitch thread) |
| Shank length | 74.5 mm |
| Ø shaft | 11.95 mm |
| Width | 34.5 mm, 6.6 mm, 11 mm, 2.7 mm |
| Height | 9.9 mm, 5.9 mm |
| Thread length | 50 mm, 40.5 mm |
| Puch |
Accessories & related products
Hot 
swiing® ingenious wheel axle with bearing conversion kit spoke hub front | Puch
Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 11.95 mm · Thread type: MF12x1 (fine pitch thread) · Ø inside: 12 mm · Shank length: 74.5 mm · Ø outside: 29.02 mm · Thread length: 40.5 mm · Thread length: 50 mm · Width across flats: 19 mm · Total length: 165 mm · Width: 2.7 mm · Width: 6.6 mm · Width: 11 mm · Width: 35.7 mm · Height: 5.9 mm · Height: 9.9 mm
EUR 46.90
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 19 mm · Thread type: MF12x1 (fine pitch thread) · Ø inside: 12 mm · Shank length: 100 mm · Ø outside: 29 mm · Thread length: 29 mm · Thread length: 53 mm · Width across flats: 19 mm · Diameter: 29 mm · Total length: 190 mm
EUR 46.90
swiing® ingenious wheel bearing 12/29/9 spoke & cast rim | Puch Maxi
Bearing type: Deep groove ball bearing · Bearing cage: Sheet steel cage ball-guided · Inner ring width: 9 mm · Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CN (standard) · Material: Plastic · Material: Steel · Ø inside: 12 mm · Ø outside: 29.02 mm · Width: 9 mm
EUR 10.70
GPO speedo drive 17" with lugs 12 mm axle | Puch Maxi S / N, X30 Sport NS / NL, NG-2AH, X30 Velux
Manufacturer: GPO · Material: Aluminum · Place of use: left · Place of use: right · Wheel size: 17 " · Ø outside: 41 mm · Ø mounting hole: 12 mm · Ø axle: 12 mm · Total height: 10 mm · Thread type: MF10x1 (fine pitch thread) · 4-edge speedometer cable: 1.8 mm · 4-edge speedometer cable: 2.6 mm
EUR 33.70
Explore categories from Hub & axle
Moped fans also bought
NTN wheel bearing 12/28/8 rear cast hub Leleu | Puch Maxi
Bearing type: Deep groove ball bearing · Stock number: 6001 · Width: 8 mm · Inner ring width: 12 mm · Manufacturer: NTN · Ball bearing closed: Yes · Dust protection type: 2RS - NBR contact seal on both sides · Bearing clearance: CM (special/noise-reduced) · Bearing cage: Sheet steel cage ball-guided · Groove ring: No · Material: Plastic · Material: Steel · Area of application: Standard · Ø inside: 12 mm · Ø outside: 28 mm
EUR 7.10
swiing® revival wheel axle LELEU & Grimeca wheel hub cast wheel rear | Puch
Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø outside: 11.8 mm · Total length: 185 mm · Width across flats: 19 mm · Shank length: 100 mm · Ø shaft: 11.9 mm · Thread type: MF12x1 (fine pitch thread) · Thread length: 26 mm · Thread length: 52.5 mm
EUR 18.00
Hot
swiing® ingenious wheel axle with bearing conversion kit rear spoke hub | Puch
Ball bearing closed: Yes · Manufacturer: swiing® ingenious parts · Material: Steel · Surface: galvanized (blue) · Ø shaft: 19 mm · Thread type: MF12x1 (fine pitch thread) · Ø inside: 12 mm · Shank length: 100 mm · Ø outside: 29 mm · Thread length: 29 mm · Thread length: 53 mm · Width across flats: 19 mm · Diameter: 29 mm · Total length: 190 mm
EUR 46.90
Hot
Inner cable set automatic | Puch E50
Manufacturer: Made in Germany · Material: Steel · Ø Stranded wire: 1.25 mm · Ø Stranded wire: 1.5 mm · Ø Stranded wire: 1.8 mm · Quantity: 4 pcs · Total length: 1600 mm · Total length: 2200 mm · Nipple shape: Barrel (transverse) · Nipple shape: Cylinder · Nipple shape: Pears
EUR 11.90
swiing® revival wheel axle set LELEU wheel hub cast wheel rear | Puch
Manufacturer: SKF · Ball bearing closed: Yes · Manufacturer: swiing® revival parts · Material: Steel · Surface: galvanized (blue) · Ø inside: 12 mm · Ø outside: 28 mm · Ø outside: 29 mm · Total length: 190 mm · Width: 8 mm · Width: 9 mm
EUR 37.30
SKF 6001 2RSH Ball bearing 12/28/8
Bearing type: Deep groove ball bearing · Bearing cage: Sheet steel cage ball-guided · Stock number: 6001 · Inner ring width: 8 mm · Manufacturer: SKF · Ball bearing closed: Yes · Dust protection type: 2RSH - NBR contact seal on both sides · Bearing clearance: CN (standard) · Ø inside: 12 mm · Ø outside: 28 mm · Width: 8 mm
EUR 15.60
Attention: new opening hours from 16.02.2026 & new evening sale on Thursday 17:30-20:00
